設計圖紙：根據個人要求設計圖紙。
Design drawings: design drawings according to personal requirements.
制造機箱：
Manufacturing chassis:
用諸如木工板的材料制造機架；
Manufacturing a frame with a material such as a wood board;
底盤高度為60-70厘米，比模型沙盤的有效面積寬10-25厘米；
The chassis height is 60-70cm, 10-25cm wider than the effective area of the model sand table;
設置沙盤：先將沙盤框安全放置，使沙盤與場地保持一致，然后鋪3-5厘米厚，濕度適中的沙子，用板材刮平壓平，作為較小等高線的平面，然后打出與地形圖對應的方格，在沙盤框周圍標明相應的編號。
Setting sand table: first place the sand table frame safely to keep the sand table consistent with the site, then pave 3-5cm thick sand with moderate humidity, scrape and flatten it with plates as the plane of small contour lines, then make a square corresponding to the topographic map, and mark the corresponding number around the sand table frame.
堆積地形：
Stacking terrain:
根據方格，在沙盤上繪制地形圖上選定的較低等高線、能控制基本地形形狀的等高線、山頂、鞍部、山腳、斜坡轉換點和河流。
According to the grid, draw the lower contour selected on the topographic map, the contour that can control the basic topographic shape, the top of the mountain, the saddle, the foot of the mountain, the slope conversion point and the river on the sand table.
竹簽中分別插入計算好的山頂、鞍部、山腳、斜向轉換點、河彎等起伏明顯的點和起伏不定的點.竹簽的高度，加上沙盤高度上的底沙厚度。
The calculated points with obvious fluctuation and ups and downs such as the top of the mountain, saddle, foot of the mountain, oblique conversion point and river bend are inserted into the bamboo stick The height of the bamboo stick plus the thickness of the bottom sand at the height of the sand table.
選色噴漆：根據圖紙顏色選擇相應顏色的涂料，將涂料噴到相應的PVC板或3D打印模型上。PVC板材需要送到設計部門雕刻。
Color selection and painting: select the paint of corresponding color according to the color of the drawing, and spray the paint on the corresponding PVC board or 3D printing model. PVC plates need to be sent to the design department for engraving.
刻制零件：根據實際情況按比例設計構造，在電腦上切割成不同的板，按要求進行設計，然后刻制各種板，送到制作部門進行制作。工業界的模型基本與建筑模型相似，按照圖紙的特定比例縮放，雕刻板，用氯仿粘合。
Engraving parts: design and construct according to the proportion according to the actual situation, cut into different plates on the computer, design according to the requirements, and then engrave various plates and send them to the production department for production. The industrial model is basically similar to the architectural model. It is scaled according to the specific scale of the drawing, carved board and bonded with chloroform.
組合零件：制造部門根據設計部門提供的各零件，并根據說明書和粘接方法，以三氯甲烷為基材，將PVC板粘接成工業模型的大致形狀。
Combined parts: according to the parts provided by the design department, and according to the instructions and bonding methods, the manufacturing department uses chloroform as the substrate to bond the PVC plate into the approximate shape of the industrial model.
整體組合：配飾制作和模型組合。
Overall combination: accessory production and model combination.
設立地物：沙盤中的地物，如房屋、鐵路、橋梁、樹木和獨立地物等，多以類似的模型來表示，公路和鄉村道路則以不同寬度的不同紙張和不同顏色的布料來表示；河流則以藍色紙張或鋸末來表示；森林則以小枝或綠色鋸末來表示.地物的大小，應與比例尺保持一致，相關位置要正確.設立地物時，應按照水系、居民地、道路、樹林和獨立地物的順序來設置。更后，在相應的位置插入地名、河名、山名、高程注記等標牌。
Establishment of features: features in the sand table, such as houses, railways, bridges, trees and independent features, are mostly represented by similar models, while roads and rural roads are represented by different paper of different widths and cloth of different colors; Rivers are represented by blue paper or sawdust; Forests are represented by twigs or green sawdust The size of features shall be consistent with the scale, and the relevant positions shall be correct When setting up features, they shall be set up in the order of water system, residential area, road, forest and independent features. Finally, place names, river names, mountain names, elevation notes and other signs shall be inserted at the corresponding positions.
Thank you for reading. Source of this article: large space model. For more contents and questions, please click: http://fustercnc.com We will continue to work hard to provide you with services. Thank you for your support!
